Small update
"Anubis" won the second place for casemods at this year's DCMM on Dreamhack.
And two more trophy´s by visitor vote.
1st place Most spectacular creation and
1st place Beauty Case
That was an absolute surprise. :clap::clap:
Hey guys,
The DCMM (germany´s casemodding championship) is now taking place in Leipzig on the Dreamhack.
And what can I say .... YEAHHH, I was able to defend my title and have actually again occupied the 1st place in the category CaseCons(scratch build) with the "Alkesh". :rock::grin:
So I'll just start.
Apart from a few missing dimensions or angles, my highest priority was the glass pyramid.
Because gluing Plexiglas was not one of my strengths to date.
After I was able to detect the missing angle by means of a tiny origami pyramid, I first created a small wooden pyramid
and...
CHEOPS
"The Pyramid of Cheops is the oldest and largest of the three pyramids of Giza and is therefore also known as the "Great Pyramid".
The tallest pyramid in the world was erected as a tomb for the Egyptian King Cheops, who ruled during the 4th Dynasty in the Old Kingdom (about 2620-2580...
Hi,
I wish you all a Happy New Year!
Here finally all the final pictures, first without lighting and then with lighting ;)
I hope you enjoyed it, I am already fully engrossed in the next project.
After three years, it's about time, next follows...
Chapter 5
Happy 4th Advent and welcome to Chapter 5, the last update.
Even though I was already more than happy with the whole project,
In spite of all this, I decided to add another round element to the front, the reactor.
First, I took some thermoforming foil and a fruit bowl and made an...
Chapter 4
Time for cable laying and everything that goes with it.
For the small round element, I attached a potentiometer to the rear end of the upper case cover.
For the wing, I glued a small piece of Plexiglas and sanded it into shape, which can easily be attached and now I can use it to...
Chapter 3
Hello and on we go.
By the way, the Strix 1070ti had to be converted to water cooling.
Now it was up to the attachment of the round elements.
The two small holes are for attachment and the big hole is for the shaft on which the wings are attached.
Now the drive.
I had...
Chapter 2
Now it goes to the reservoir.
First I cut me a 5mm thick aluminum rail as a carrier for mounting
this then provided with the corresponding holes
and shaped the ends to match the housing screws
Now I had to equip the premium AGB holders of Bitspower with an additional thread...
Time for the first update.
First, I built the head out of paper.
Sounds easy, but it is not XD
So I could now transfer the measurements from the paper head to Plexiglas and have cut this.
Depending on how large the existing plexiglass was, a circular, stitch or the scroll saw was used.
For...
Welcome to my next project
"Anubis"
Anubis is portrayed in old traditions as a jackal,
whose task was to lead the souls of the people into the land of the dead.
In this project a jackal head should be polygonized and adapted to the Cougar Conquer.
I have had this idea for a long time but when...
Thx guys thx (y)
Hi, sorry for my delay, I had a sick cat at home the last few weeks and had to go to the vet almost daily.
At the moment my cat seems to be better but the cause still could not be found.
So I still fear daily for his life :(
So as promised here a short video of the Alkesh and...
Sooo the wait is over.
Here is the last update.
Next it went to the new 1cm bracket.
After all edges were beveled I bent them now differently to change the angle of Al`kesh something.
So it feels a bit more coherent and you can look much better into it.
The whole pyramid was now covered...
many thanks guys (y)
Lets go, it was a bit stressful the last two weeks but it was worth it.
That's what he looks like now the "Washing Effect".
I have used black acrylic paint for this and also some of metallic effect colors on acrylic base (black, silver, anthracite, gold)
The colors are...
Here I am again.
This time there were many low blows but it goes ahead.
Where had I stopped?
Achso, the Alkesh I have now completely painted outside silver.
and then remove all the tapes.
Although the film is good for masking because no color runs behind but the paint has decomposed the film...
And on it goes, I completely forgot that the Modding Masters already on 2.-3.6.18 is.
I really wanted to be done so now we have a Deadline.
As I mentioned earlier, there was a lot to fill and to grind.
The IO panel should still be clad with ribs, after long thinks whether Plexi or Alu I...
So that was a short week but it went forward.
The base plate of the bracket has been polished.
The acrylic glass rod I have now glued to the base plate.
Now I put the holes for the holder in the Alkesh
I then filled the cavity (between the attached trapezoid of the rads and the...
Sooo let's go on.
There will be a lot to report after this weekend :cool:
Where do I start?
I pretty much worked on all areas in parallel, but sorted the images by topic to keep things more manageable.
The drives were finally fastened.
Since the fiber putty is hard after 5min I held each...
Hello,
The first thing I noticed in this photo was that something was wrong on the IO-Shield.
I did not notice the tinkering, although I had marked lines was the lettering good 5mm wrong.
I was maybe a little annoyed because the font for the plotter was too small.
okay fixed
Now it was...
Hello ,
All cut surfaces were sanded and deburred
then cleaned and masked with polyester adhesive tape and glued.
Of course, the first attempt went awry. When masking I kept the scalpel too oblique, so the gap was too big and I could only remove the excess adhesive by force.
I even had a...
Tek´ma´tek Tauri!
Now it went to the MB tray.
To measure it, I just measured every two inches from the center
and put me on the tray points.
so I could accurately as possible to cut the aluminum.
now the riser card
and cut the threads for it
then all holes and spacers were set...
Hello and Happy Easter!
This time a monster update.
I have a lot tube remains but nothing fits for a engine
I found 4 feets for shop shelves
and yeah I think that suits.
and lenses to illuminate each engine from the inside
Then the Ballistix Sport LT.
I remove the decals and...
Hi!
after I covered everything with the fine polyester knife it went to the bottom.
Exactly the same procedure as above
Now the Back had to be straightened, but I needed a guide rail.
Paper helps very well as a ruler replacement if you want to cut polystyrene,
So I cut the shape...
Now it's going on again.
As previously mentioned I've sended the VGA to Alphacool, which arrived there at the beginning of 10/2017. As a hint, I should calculate with 20 days for the mapping. (ca. 11/2017) and 8-12 weeks manufactoring, so max 01/2048 - 03.2018.
The VGA was sended back short...
Hello,
Now the last update
We remember, the stat at Gamescom
but there were still little things in which I just did not know how to implement them
1.right, the ornaments behind the mouth
2.middle, the yellow clips on the barrel and
3.left, the clips on the reservoir
first 2.
i cut...
Hi,
sorry for being to late but I was a little bit sick.
As promised the paint Job.
To get rid of the wood grain I painted it twice with this one.
Call it Plastic seal but it's like clear coat.
the colors used
over 100 parts
I have coated these parts with textured paint...
Heyho !
now i Need extern usb ports
for the cable
these alu parts have made me really ready
bevor the paint job i set all holes for the tubes
Loop complete,
how you can see, you see nothing XD
holder for the res
Here the panel in front of the handle, so you can not look...
Hi,
now the handle.
For this I chose Multiplex,
a groove for the cable from the trigger
:mrgreen:
now I have made the grip by deep drawing.
the trigger
left side the final shape from the trigger
more 3mm and 5mm MDF
The final shape...
The
Goa´uld Al´Kesh
is a space ship of the bomber class from the TV series Stargate SG1.
What is there to say?
Designation: Al'kesh
Builder:Goa'uld
Class:Bomber
First appearance:SG1_04x22SG1 4x22 Exodus
Sheath material:Naquadah
Hyperdrive:interstellar
Arming:Goa'uld-Gun,Goa'uld-Bombs...
Hi,
it's time again, my weekly update.
At some point it had to be done, the water cooler on the VGA mount
then I needed a bracket for the magazine, 4 x 22mm MDF cubes
the mount for the riser cable
Monitors can also be connected via an angled HDMI adapter
now the top...
Go on,
this time unfortunately no particularly good series of photos
but the little things are just the project to do what it is.
the MB Tray
glued with Sikaflex chassis glue
and now it went to the magazine, the cover for the radiator and the power supply...