Hi,
Thanks for the link. I checked in the Intel site and ran the program to check my machine. After checking the machine, it listed a few drivers including Graphics, chipset software etc. However there was message under each driver saying "This device is unknown or unresponsive. Please contact...
Hi,
Thank you for the link and I did check. There were only two driver files (BIOS and Ali Sound driver) it could recognise. I downloaded the both and updated the sound driver. No improvement I could see.
Do you think I need to update the BIOS as well? Any other suggestion for this slow...
Thanks for the information.
Could you please advice me how to identify the correct chipset driver for my Toshiba Lpatop?
It is nearly 12 years old. The drivers I should look in Intel site or is it coming from XP?
I also found my microphone not working while speakers are working. I could not...
Hi, I found the info about DMA mode. I have posted the question (how to check DMA...) twice and please ignore the last query.
I found the following controller (and settings) in the device manager.
+IDE ATA/ATAPI Controllers: (Under this there are 3 controllers/channels)
- Ali M5229 PCI Bus...
>Check to make sure the proper chipset (specifically, the mass storage controller) is loaded and working properly<
Could you please let me know how to check this?
Also to check whether the laptop is working in the DMA/PIO mode?
Thank you.
Hi Thanks for the info.
I appreciate if you could let me know how to check whether the proper chipset (specifically, the mass storage controller) is loaded and working properly?
And how to check whether the DMA mode is running and not PIO.
Cheers
HFdo
Thats a good point. I didn't think about it. It has an ATA (16GB) hdd. Is there a way to check this hdd? whether it is working correctly with the spin speed (rpm) etc.?
Hi All,
I have an old Toshiba Satellite laptop which has only (maximum) 512Mb of RAM, 1GHz processor. It had Windows 2000 and was working ok.
There was problem and I had to format the HDD and installed XP and SP1, 2 and 3.
The laptop is, now, painfully slow. Example, if I double click the...
Hi All,
I have an old Toshiba Satellite laptop which has only (maximum) 512Mb of RAM, 1GHz processor. It had Windows 2000 and was working ok.
There was problem and I had to format the HDD and installed XP and SP1, 2 and 3.
The laptop is, now, painfully slow. Example, if I double click the...
Hi all,
I have ThinkPad W500 laptop and I recently installed & update to Windows 7, from windows XP.
After the installation I found two improper functions.
1) USB port. When I connected my USB pen-drive and then stopped from taskbar, I get the message saying it si now safe to remove the...
Hi all,
I have ThinkPad W500 laptop and I recently installed & update to Windows 7, from windows XP.
After the installation I found two improper functions.
1) USB port. When I connected my USB pen-drive and then stopped from taskbar, I get the message saying it si now safe to remove the...
Thanks for the prompt reply.
I have selected the 'clear type test'.
I could not find the option in Windows 7 to set separate resolution for both LCDs? Do I have to download any other program for this?
Hfdo
Hi All,
I have Lenovo/Thinkpad W500 with dedicated 512Mb Graphic card.
I recently installed Windows 7 OS system. After the new OS installation the fonts on the LCD screen are not sharp and clear. Also some of my icons (in the Task bar) too lost the sharpness. They look like bit blurred...
Some good thing happened. I can go on wireless with my router. I conncetd my ethernet cabel to on of the LAN port and disable the DHCP, and set the IP, Gateway, Subnetmask and DNS settings in the router.
I now can acccess internet through wireless.
But My router doesn't show the Internet...
Hi Again,
I disabled the DHCP (in the LAN port configuration in the router) as suggested. And then went to the Basic setting page of the router and entered IP address, Subnet Mask, GateWay address and DNS of my Ethernet connection. And then connected the internet to the LAN port. It is not...
I would also like to know, whether it is possible to configure one of the for LAN ports to be a WAN port so that I can connect my internet cable to the WAN port?
eg. Can I configure LAN1 to be WAN and keep LAN2, LAN3 and LAN4 as they are (as LANs)?
>>So what you need to do is go into the router/gateway and turn off the DHCP. Then setup your wireless settings how you want. Now just plug in a regular patch cable from an ethernet port on the router to the jack. Then you should be able to access the internet using your wireless.<
Thank...
Hi, Thank you for the prompt reply.
To answer your questions, yes I do get internet over the Ethernet connection. I am in fact living in a building where there are many apartments and I am living in one of the apartments. If I connect my laptop directly to the wall Ethernet socket using a...
Hi All,
I have Netgear N300 (DGN3500) Wireless Gigabit ADSL2+ Modem router.
The Router has a phone socket (that is RJ 11 socket) to connect to the Internet. But in my home I have Ethernet socket on the wall. That means the Internet is coming through Ethernet cable. Can anyone advise me how...