Windows 10 x64: Updated Nvidia drivers to 355.98 on my 680GTX, completely lost any HDMI output, tested 3 TV's nothing, tried clean re-install of 355.98 still nothing, force detection nothing. Uninstalled Nvidia Driver and poof its back. Preformed a clean install of 355.82 rebooted and again...
Finally got the DP to DVI cable and installed it today, again no success. It will not allow the 3 monitors I want to be set as a group, no matter how they are attached. As far as I can tell this is a driver issue, since everything states this is supported and should operate correctly, have to...
The more I play with it the more I think it is a driver issue, no matter what else, if the 2405 is plugged in (HDMI using a DVI, or either DVI port), then it is always forced to be part of the Surround Configuration, any of the other monitors can be present or not depending upon what input is...
It will only allow the HDMI, DVI and Display Port to be used (which would be fine if I could select which DVI), but the issue is the DVI selected is always the wrong monitor (if I unplug one then it select the correct set, but as soon as I plug it back it poof wrong one again), no matter which...
I have 4 monitors (1920x1200), I want to span over 3 of the four.
Since I have 4 I'm using them as follows:
4
DVI-1
3 2 1
HDMI Display Port DVI-2
All are set to the...
Ihave 4 of these: 3 Way Adjustable Tilting Wall Mount Bracket for LCD LED (Max 33Lbs, 10~25inch)
Not the best mounts of all times, but for the price hard to match. They do adjust (by 3.5 inches), which was enough to get everything squared away, so long as you plan ahead.
Wish I could, but I need the CUDa processing, so Nvidia it is. Anyways here how I fixed it.
As I said both cards (Nvidia and AMD) work at the same time, restored then booted up with the Nvidia and AMD present, allowed both drivers to be installed, switched outputs to Nvidia, rebooted came...
First off I use to use Nvidia all the time, then I moved to ATI and followed them to AMD, while not always the fastest I always had good luck with them, now I found I needed CDUA so I bought an Nvidia 680 to replace my aging AMD 5750 (its over kill, but was a good price). Thus I:
1. Uninstalled...
I have an ASUS Rampage III with an x980 happens at stock. I'm booting off a Vertex 3 240GB, with a secondary Gskill 120GB. Now the Gskill was the old boot drive and I've had this system for a full year without too many issues (even OC'ed), but lately I've had it. Windows 7 boots and runs like...
As I said its not much faster using iometer it about 5% so nothing to write home about, but every little bit helps, still not something I'll miss.
I assume you mean turn off "Hard drive after", which I have set to 0 (never)
PCI Link Sate Power Management (off)
Agreed: I have a wacom...
I've moved to the Intel, for now, I actually found the Marvell slightly faster, mostly I assume because it spread out the load some, but moving back to Intel does nothing for the immediate issue, which is the 120GB GSKILL SSD, this was the old boot drive on this system, before switching to the...
120GB GSKILL SSD failing out with message:
An error was detected on device \Device\Harddisk0\DR0 during a paging operation.
When this occurs I need to reboot, after rebooting it will work fine, but after the system has been running for a few hours, or I sleep and resume a few times, I will...
should not be I've used the same drive and controller on an i7 980x (ASUS) with both of these drives without issue, so its not a driver issue or the like, that would still point the the MB being the issue.
ERIC
Well I think it happens with SATA2 drives as well as the other SSD I tried was and Intel (generation 2 80GB Drive). I personally think it might be related to SP1 (since I never saw it before I reinstalled and updated to SP1), but I have no proof of that and my use of the system was limited at...
I have the latest BIOS on both the MB and Drive, but am felling better that I'm not alone, in my case as I said it is mostly just annoying. I no longer think it is the drive, as I tried switching to an Intel SDD and I saw the exact same MO, just less pronounced (happens for less duration as far...
I have an ASUS P8P67 deluxe MB (version 3) and a Vertex 2 120GB drive, my problem is randomly it hangs for a period, it normally only lasts a minute or so, and running tasks continue, without issue, but starting new tasks fail, the cause seems to be that the executables can not be found...
So I've been trying to play nice for the last 6 weeks, I bought a BizLink which did not work and returned it to Dell. I then bought an Accell adapter, and it was even worse (did not work at all before I updated BIOS, there after it just flickered), since returning to the reseller was a major...
Accroding to the website my adapter is supported:
Accell B087B-002B 1.01 DisplayPort DVI (Dual Link, Active Dongle) 2560x1600 Validated accellcables.com
yet it does not work at all with the original bios and it flickers with the updated bios, but then again if I update the bios the I get...
Reflashed and did some more testing: The glitches are related to handling window borders (resizing, passing across them ...), this happens with both 9.12 and 9.12beta. This can be fixed by disabling the Aero effects (cold booting did nothing), but then that is not an acceptable long term...
Gave it a try, downloaded and flashed using: ATI.HD5870.1024.091112.bin
Flashing was quick and easy went well both times.
Flashing did not do anything to fix the DP connected panel (still flickered about once a second).
Second one of the DVI monitors stopped working correctly (would get...
Requested support and a replacement from ACCELL and the response came from Bizlink, so I feel it is safe to assume they are one in the same, also given the pictures of the new ones being released I think it is same to assume that are also just rebranded Bizlink adapters.
In case you are...
I have 3 Dell 2405WFP Monitors on my 5870
2 are Hooked using DVI
1 is hooked up using the Bizlink (Dell)
The Bizlink one constantly flickers and I have tried
All three monitors.
Different DVI cables (which all work when hooked up to DVI). and all are heavy duty dual link monoprice cables...