Search results

Hi, I have a Dell 2700w rack UPS and I would like to set it to High Efficiency mode. It's currently in Normal mode. I'm able to get into settings from the control panel on the unit, but can't seem to change the settings. I've also tried to reset the settings to defaults, but can't seem to do...

Thank you! I'm able to get 128GB working at 3133 C16 at 1.35V. If I try 3200, I can't get past the bios screen. However, I notice that the bios is very sluggish...is there a reason why that would be?

Thanks...do you mean generally, a bios will read the XMP of all installed sticks and use the lowest settings?

Hi, I have a Threadripper 1950X system and I'm trying to run 128GB of RAM using a mix of 4 Ripjaws V 3600C16 sticks and 4 RipJaws V 4000C18 sticks. The 3600C16 sticks are rated to run at 1.35V and the 4000C18 sticks are rated at 1.4V. Is it safe to run the 1.35V sticks at 1.4V? When mixing...

Hi, brand new drive. crystaldiskinfo is showing temp of 50 degrees. Is this normal? It’s not shucked so running in upright position is original case. Thanks!

On my X399 mono, I have a 1882ix and 1880x and while they don’t show up in POST, Windows recognizes them and have had no issues. I have CSM turned on, but not sure if that makes a difference. Love these cards!

So are the BestBuy Easy Store 14TB drives 5400 or 7200? Or are they 7200, but operate at 5400 due to firmware. Separately, has anyone noticed a 64 drive limit for ChrystalDiskInfo? I can't find info on that anywhere! Thanks!

Yes, thanks…settled on 1.1 for soc and 1.44 for RAM. I can go a little lower and still pass memtest, but with the lower settings, the system does not boot from a cold start (Eg., the bios will try a few times to boot, and eventually give up and revert to stock settings). The higher values...

Hi, do you mean 1.35 for SOC? I'm able to get it running using 1.1V for SOC, but I need 1.44 or 1.45 on the RAM.

Sorry for not being clear...I mean the bios will turn the computer on/off a few times and the default the RAM back to stock speed. (2666, I think). I am now able to pass Memtest using 1.1 SOC and 1.44 RAM. Everything else Auto or whatever Optimized Defaults give me. I wonder why the kit is...

I’m not an expert either, but I think 2 vs 4 dimms make a difference.

Hi, thank you for the advice! Board finally booted at 3600 using 1.1 SOC and 1.45V. Lowered that to 1.44 and that booted fine too…running memtest to test stability.

Yes, the 128gb kit is on the QVL

Hi, running above with a 5950X and the latest BIOS 3601. The kit I have is the 4 stick G.Skill Trident Z Neo F4-3600C18Q-128GTZN and it’s on the board QVL. But I can’t get it to boot at anything higher than 3200. I’ve also tried Ryzen Dram Calculator, but still no go. Anyone else have this issue...

Hi, wanted to see if someone can help me with my Areca 1880X RAID6 array which is in a degraded state after I accidentally turned off my Supermicro JBOD enclosure. When I turned the JBOD enclosure back on, a bunch of the disks in the array were marked FAILED and the array was marked FAILED. I...

Hi, I’ve been testing StorageSpaces and found that the default settings leads to horrible performance. I am testing a 12 x 3 TB pool with dual parity and using the GUI to create a virtual disk, I was getting 3-4 MB/s write speed. After some googling, I found that the Interleaved parameter has...

Hi, I have a home built with the above setup and I'm trying to figure out how to get the system to recognize new hot plug drives. When I add new drives to the enclosure, they are not recognized until I reboot the system. "Refreshing" in Storage Spaces does not bring up the drives. Is there...

Can you tell me which ones to post? Thank you.

Hi, my ReadyNAS became unresponsive and I had to hard reboot the device. When the device rebooted, it looks like I lost my volume. When I log into the admin screen, I see the message “Remove inactive volumes to use the disk. Disk #1, 2, 3, 4, 5, 6” Any suggestions on what I can do to recover...

Just installed the latest intel chipset drivers and same issue...just can’t figure it out!

Bios is up to date and HT is enabled in bios. also tried msconfig and number of processor box is unchecked and if I check it, I only see options for up to 4 processors (vs. 8 with HT). It’s a work computer and so could it be that the image that was used for the hard drive is bad? But I can’t...

Hi, I have a Dell Latitude 5400 laptop with a i7-8665U CPU and HT is enabled in BIOS, but in Windows, it’s showing Cores: 4 and Logical Processors: 4. I’ve googled a bunch, but can’t find any references to a setting within Windows to change this. Has anyone seen this before and any idea how I...

Budget's not huge...was going to buy used and it looks like HP has based library software for free. It's just I can't find any info on tNAS (which I assume is not free). After some digging, it sounds like HP licenses it from Qstar...does anyone have any experience. I guess it can't be all...

Yeah, that looks cool, but probably not within budget...anyone have experience with HP's Tape as NAS, or t-NAS?

Yes, I will need to get a LTO library...

It looks like HP has a product called Tape as NAS which sounds like exactly what I am looking for. Does anyone have experience with this product? How much does it cost? Thanks, Hammer

Thanks. That’s very helpful. does any know if a tape library will also be seen by Windows this way? Eg., can it be mounted and accessed by a Drive letter? Is each tape in the library a different drive letter or does it show up as a single drive letter spanning the capacity of all the tapes...

Hi, was wondering if the group here can help guide me in the right direction: 1) I have 75-100 TB's of data than I need to keep online or near-line. 2) These data sets do not change and seldom deleted 3) Currently, we are storing them in a large RAID 6 array, and have a duplicate array for...

Hi, does this board support SR-IOV? Thanks!

Hi, has anyone been able to get SR-IOV working on an X399 motherboard? I'm trying to passthrough a LSI 2308-8e SAS card to a Hyper-V vm running FreeNAS, but have not has much success. I have a Gigabyte Aorus Gaming motherboard with the latest bios. I've enable IOMMU in bios, but Server 2016...

That’s very helpful. Thank you all for the advice.

Thanks...I’m not looking for technical support...just the firmware image...any other thoughts?

Hi, I purchased a WS-C4948E-S switch off ebay...does anyone have IOS 15.2 firmware for this unit? Thanks!

Hi, I also have this issue with a RAID6 array on a 1882 card except it's copying large files (say 40 GB's) from a SSD on Windows 10 to the array on Server 2016. Both machines have Mellanox ConnectX-3 cards running at 10Gbps. I always thought it was how the cache buffering works so never...

Yeah, thanks. I took it apart and I can’t believe how complicated the inside is. Can possible get it to work by rewiring it, but unlikely without...Thank you.

It’s are Dell 6607 if anyone is familiar with that. Would I be able to wire my one hot to all 3 hots on the PDU? I don’t think so and I am afraid to try!

Right, I understand I won’t be able to get 208v...I was just trying to use it as a PDU for 120v devices.

Hi, I have a 3 phase 208v PDU which comes with a 4 prong L15-30 plug that I would like to use at home. is there a way to re-wire the plug and attach a new plug so it works on a standard home outlet? I tried wiring ground to ground, hot to one of the hots on the PDU and connecting neutral to...

Wow! I tried 2666 with 20-20-20-50 at 1.35v and I can’t seem to get through even 1 pass of memtest. I am using 4 sticks of CT16G4WFD824A on Aorus x399 gaming with a TR1950X. Any suggestions on settings I should try?

Hi, running 4 x CT16G4WFD824A - micron 16 GB ECC UDIMM in a TR 1950X system. Does anyone have OC experience with this memory they can share? Thank you!